Just How to Install a Bathtub Yourself
Just How to Install a Bathtub Yourself
Blog Article
Were you hunting for advice around How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bath tub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and also sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a moderately tough task. If the old bathtub is readily available, the job can relocate speedily; if you have to open a wall surface to get rid of the old bathtub and position the new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub as well as set in the brand-new one. See to it you have actually qualified yourself for the job as well as are comfortable trying it. As opposed to hiring a specialist to take control of a halfway-completed task, it is better to consider utilizing one prior to you start. Chances are you may need an expert plumber to make tube links.
This write-up will aid you mount a brand-new bath tub in your bathroom if you have currently bought a brand-new bathtub and also do not require to transform the setup of your previous water pipelines.
Your devices and also product list must make up the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. When the supply pipes have been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Before carrying on to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washers remain in location between the faucet and the sink. Safeguard the faucet in place with the maker provided backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap ports. The previous type needs to be connected to the faucet finishes initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Tub
Using both wooden boards under its feet, put the bath tub in the needed setting. The wooden boards are practical in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four tiny factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the level and changing the feet on the tub till the spirit level reads degree.
To install taps, fit all-time low of the outermost flexible tap port to the proper supply pipeline by making a compression join; then do the very same for the other tap.
Activate the water supply as well as examine all joints and new pipework for leakages and also tighten them if necessary. Fill up the bath tub as well as also inspect the overflow electrical outlet and also the normal electrical outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the bathtub ought to wait up until the tub has actually been utilized a minimum of once as this will resolve it right into its last placement.
Preparing for the Setup
First of all, the sustaining structure provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its last setting.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to crack an inflexible seal, triggering the water to permeate the wall surface in between the bath and also the tiling, resulting in complications with wetness and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components and installations. They are offered in tubes and also cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can split fairly early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly available on the marketplace. It is advisable to fit the floor tiles using waterproof or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic reader about How to Install a Bathtub, I figured sharing that piece of content was worth the trouble. Kindly take the time to share this page if you appreciated it. I praise you for your time. Kindly stop by our website back soon.
Go Services
Report this page